COMX 52CA-COS
Active

Communication module SPI - CANopen Slave

The module for all communication tasks
  • Universal CANopen Slave interface with network connector onboard

  • Allows a flexible positioning of the network connector

  • Host connection via dual-port memory or SPI

  • Function-compatible substitute for comX 10CA-COS

The module for all communication tasks

The comX communication module is designed to be integrated into automation devices to provide drives, robot controllers, PLCs, etc. with a network interface. Communication tasks are all executed autonomously in the module - irrespective of the processor of the target device.

Process data is exchanged via a Dual-Port-Memory per access by an 8-/16-bit bus interface or a fast 50 MHz SPI interface.

comX supports all leading Real-Time Ethernet protocols as Master or Slave and meets all network-specific requirements in just one single module. To support a line topology, the module is equipped with two Ethernet ports. The communication protocol can be changed simply and reliably by loading the appropriate firmware and a software license for masters.

Due to the Hilscher network controller netX, a 10-year delivery guarantee is granted.

COMX 52CA-COS

Parameter

Value

Product

Part number

1581.540

Description

Communication module CANopen Slave

Communication controller

netX

netX 52

Integrated memory

Flash

4 MB SPI Flash EPROM

Voltage/power supply

Supply voltage

+3.3V DC ± 5%

Typical/maximum current consumption

370 mA / 400 mA (at 3.3 V)

Typical power consumption

1.25 W (at 3.3 V)

Connector

Via system bus interface X1

System interface

Type

Parallel or serial dual-port memory interface

Connector

50-pin SMT connector, socket

Pin distance

1.27 mm

Dual-port memory size

16 KB (lower 8 KB used by firmware)

Data width

8/16 bit, switchable

Serial dual-port memory interface

SPI slave, mode 3

Baud rate

max. 50 MHz

Communication interface

Communication standard

CANopen Slave

Interface type

ISO-11898, isolated

Complies with the CANopen specification EN50325/4

Connector

DSub plug, 9-pin

Transmission rate

10 kBits/s, 20 kBits/s, 50 kBits/s, 100 kBits/s, 125 kBits/s, 250 kBits/s, 500 kBits/s, 800 kBits/s, 1 MBits/s

Diagnostic interface

Type

UART or USB

Connector

Signal on the host interface. Available only if integrated with host system.

Display

LED display

SYS system status, green: RUN, yellow: RDY

CAN communication status, green: STA, red: ERR

Operating elements

Network address

2 rotary switches for address

Environment

Operating temperature range

-20 °C … +70 °C (Air flow during measurment: 0.5 m/s)

Temperature range for storage

–40 °C … +85 °C

Humidity range

10 % ... 95 % relative humidity (non-condensing)

Device

Dimensions (L x W x H)

70 mm x 30 mm x 21.5 mm

Weight

approx. 35 g ... 40 g

Mounting

Using screwable metal bolts, according to comX Design Guide

Configuration

Configuration software

SYCON.net

Compliance

RoHS

Yes

Compliance with EMC guidelines

CE marking

Yes

UKCA marking

Yes

Emission

EN 61000-6-4

Immunity

EN 61000-6-2

Electrostatic discharge (ESD) according to EN 61000-4-2:2019-12 (Air discharge method)

± 8 kV, criterion A

Electrostatic discharge (ESD) according to EN 61000-4-2:2009-12 (Contact discharge method)

± 6 kV, criterion A

Fast transient interferences (Burst) according to EN 61000-4-4:2013-04

± 2 kV, criterion A (communication lines, shielded)

Surge voltage according to EN 61000-4-5:2019-03

1 kV, criterion A (communication lines, shielded)

Product name

Part number

Brief description

COMX 52CA-COS

1581.540/COS

Communication module SPI - CANopen Slave