COMX 100CN-CO Active
Communication module dual-port memory - CANopen

Flexible communication module for automation

Universal CANopen interface (Master or Slave) with network connection to the mainboard
Allows a flexible positioning of the network connector
Master or slave on the same hardware
Usable immediately due to preloaded firmware
Host connection via dual-port memory

The module for all communication tasks

The comX communication module is designed to be integrated into automation devices to provide drives, robot controllers, PLCs, etc. with a network interface. Communication tasks are all executed autonomously in the module - irrespective of the processor of the target device.

Process data is exchanged via a Dual-Port-Memory per access by an 8-/16-bit bus interface or a fast 50 MHz SPI interface.

comX supports all leading Real-Time Ethernet protocols as Master or Slave and meets all network-specific requirements in just one single module. To support a line topology, the module is equipped with two Ethernet ports. The communication protocol can be changed simply and reliably by loading the appropriate firmware and a software license for masters.

Due to the Hilscher network controller netX, a 10-year delivery guarantee is granted.

Technical Data

COMX 100CN-CO	Parameter	Value
Product	Part number	1532.500
Product	Brief description	Communication Module CANopen
Communication controller	netX	netX 100
Integrated Memory	RAM	8 MB SDRAM
Integrated Memory	FLASH	4 MB serial Flash
Power supply	Supply voltage	+3.3 V DC ± 5 %
	Typical/maximum current	approx. 450 mA … 480 mA (at 3.3 V)
	Typical power consumption	approx. 1.5 … 1.6 W
	Power connector	via system bus connector X1
System interface	Type	Parallel Dual-port memory interface
	Connector	50-pin SMT connector, socket
	Pin distance	1.27 mm
	Dual-port memory size	16 KByte
	Data width	8/16 bit
Communication interface	Communication standard	CANopen
	Interface type	ISO-11898, potential-free
	Connector	30-pin SMT connector, socket, grid distance 1.27 mm, matching with plug type SAMTEC TFM-115-02-S-D–A
Diagnostic interface	Type	UART or USB
Diagnostic interface	Connector	Signal at host interface. Available only if integrated in host system.
Display	LED display	Signals at X2 for SYS System Status, green: RUN, yellow: RDY
Display	LED display	Signals at X2 CAN Communication status, green: STA, red: ERR
Environment	Ambient temperature range for operation	-20 °C … +65 °C (Air flow during measurment: 0,5 m/s)
	Ambient temperature range for storage	-40 °C … +85 °C
	Humidity range	10 % … 95 % relative humidity (non-condensing)
Device	Dimensions (L x W x H)	70 mm x 30 mm x 21.5 mm
	Weight	approx. 35 g ... 40 g
	Mounting	using screwable metal bolts, according to comX Design Guide
Configuration	Configuration software	SYCON.net
Conformity	RoHS	yes
Conformance with EMC directives	CE sign	yes
	UKCA sign	yes
	Emission	EN 61000-6-4 / BS EN 61000-6-4
	Immunity	EN 61000-6-2 / BS EN 61000-6-2
	Electrostatic discharge (ESD) according to EN 61000-4-2 / BS EN 61000-4-2 (Air discharge method)	EN 61000-4-2 / BS EN 61000-4-2: ± 10 kV, Criterion B
	Electrostatic discharge (ESD) according to EN 61000-4-2 / BS EN 61000-4-2 (Contact discharge method)	EN 61000-4-2 / BS EN 61000-4-2: ± 6 kV, Criterion B
	Fast transient interferences (Burst) according to EN 61000-4-4 / BS EN 61000-4-4	EN 61000-4-4 / BS EN 61000-4-4: ± 2 kV, Criterion A (Communication lines, shielded)
	Surge voltage according to EN 61000-4-5 / BS EN 61000-4-5 (Communication and data lines)	EN 61000-4-5 / BS EN 61000-4-5: 1 kV, Criterion A (Communication lines, shielded)