Active
Real-Time-Ethernet solution on minimum footprint
netRAPID is the rapid and secure alternative to developing your own slave using a communication controller. As stamp-sized netX chip carrier, it is integrated into the customer hardware in the same way as a QFP part. It is designed for automated SMD series production as well as for rapid prototyping.
neRAPID 52-RE is optimized for minimum space requirements. Means the 32 x 32 mm compact netX carrier contains all necessary operating components, such as magnetics, SQI flash and netX multi-protocol chip. Its focus is on Real-Time Ethernet communication and the protocol stack will be executed in the internal RAM of the netX. With netRAPID 52-RE the hardware development is reduced to only adding network connector and LEDs. A simple 2-layer baseboard is sufficient.
Full functionality of netRAPID is enabled via licensed firmware, which needs to be acquired once and loaded during manufacturing process.
Product | Product name | NRP 52 |
Part number | 7670.100 | |
Brief description | Chip carrier with Ethernet interface | |
Network controller | netX | netX 52 |
Integrated Memory | RAM | 4 MB serial Flash EPROM |
Power supply and current | Supply voltage | +3,3 V DC ± 5 % |
Maximum current (typically) | 520 mA/600 mA (at 3,3 V) | |
Power consumption (typical) | 1.8 W | |
Host interface | Type | Parallel dual-port memory or serial dual-port memory (SPI, mode 3) |
Connector | 76-pin solder contacts 1 mm with 1.5 mm grid | |
Dual-port memory size | 16 KB (14 address lines) | |
Width for the data access to the dual-port memory (DPM) | 8 or 16 bit | |
Baud rate (serial dual-port memory) | Max. 50 MHz | |
Communication interface | Communication standard | Ethernet |
Interface type | 100BASE-TX or 10BASE-T, isolated | |
Diagnostic interface | Type | USB or UART, the support of the diagnostic interface depends on the loaded firmware |
Connector | USB or UART: Signals at Chip Carrier, available only if integrated in host system | |
Display | LED displays | SYS System status |
COM0, COM1 Communication status | ||
2 x Link and 2 x Activity | ||
Permitted ambient conditions | Ambient temperature range for operation | -20 … +70 °C (at an airflow of 0.5 m/s) |
Device | Dimensions (L x W x H) | 32 mm x 32 mm x 4 mm |
Weight | approx. 4 g | |
Conformance with EMC directives | Emission | EN 55011:2009 + A1:2010 Class B (Conducted), A (Radiated) |
Electrostatic discharge (ESD) according to IEC/EN 61000-4-2:1995 (Contact discharge method) | 6 kV Criterion A | |
Radiated RF, according to IEC/EN 61000-4-3 and IEC/ EN 55011 80-1000MHz, 10V/m, 80% AM / 1kHz | Class A | |
Radiated RF, according to IEC/EN 61000-4-3:2006 1.0-2.7 GHz, 10V/m, 80% AM / 1kHz | Class A | |
Fast transient interferences (Burst), according to IEC/EN 61000-4-4:1995 (Communication and data lines) | 2.2 kV Criterion B | |
Surge voltage, according to IEC/EN 61000-4-5:1995 (Communication and data lines) | 1 kV Criterion B | |
Conducted RF, according to IEC/EN 61000-4-6:2009 0,15-80 MHz, 80% AM / 1kHz | Class A |
Product name | Part number | Brief description |
---|---|---|
NRP 52-RE (TRAY) | 7672.100 | netX52 Chip-Carrier incl. Magnetics - EtherNet/IP Adapter |
Product name | Part number | Brief description | |
---|---|---|---|
NRPEB 52-RE | 7600.200 | netRAPID 52 Evaluation Board - Real-Time Ethernet | NRPEB 52-RE |
NXPCA-PCI | 7902.100 | netX PCI adapter board | |
NRPLFW-PNS | 7601.850 | netRAPID 51/52 Loadable Firmware - PROFINET IO Device | NRPLFW-PNS |
NRPLFW-ECS | 7601.120 | netRAPID 51/52 Loadable Firmware - EtherCAT Slave | NRPLFW-ECS |
NRPLFW-S3S | 7601.160 | netRAPID 51/52 Loadable Firmware - Sercos Slave | NRPLFW-S3S |
NRPLFW-EIS | 7601.830 | netRAPID 51/52 Loadable Firmware - EtherNet/IP Adapter | NRPLFW-EIS |
NRPLFW-PLS | 7601.180 | netRAPID 51/52 Loadable Firmware - POWERLINK Controlled Node | NRPLFW-PLS |
NRPLFW-OMB | 7601.860 | netRAPID 51/52 Loadable Firmware - Open Modbus/TCP | NRPLFW-OMB |
netRAPID is the rapid and secure alternative to developing your own slave using a communication controller. Since the netX chip carrier is the size of a stamp, it is integrated into the customer hardware in the same manner as a QFP part. It is designed for automated SMD series production as well as for rapid prototyping.