Exchangeable Module PCI Express - PROFINET IO Device

Can be mounted at any point of the delivery chain

Product Image


NJ 100EN-RE_PNS-Image



At a glance

  • Universal Master - Slave interface in closed IP40 housing
  • Host connection via PCI Express
  • One hardware for all Real-Time Ethernet protocols
  • Easy slide-in mounting without tools
  • Locks and connects without additional components on the baseboard
  • Firmware update via integrated WebServer

Weitere Informationen


The PCI Express communication module

The universal communication module netJACK with its PCI Express interface addresses in particular the embedded market with high-performance CPUs like Intel Atom®. Alternatively, there are versions with a traditional dual-port memory and a fast serial SPI interface.

All types have the compact design of a closed IP 40 module which can be mounted without using tools. Additional costs for the device will not arise because connector and mounting rails are designed as contact areas and cut-outs on the baseboard.

netJACK can be mounted quickly and easily right before shipment - or even by the end customer.

With netJACK customers can realize the full range of communication solutions, e.g. for drives, HMI or ident systems. At the same time, additional functionalities as PLC, visualization or individual applications are possible. For customer-specific requirements, Hilscher offers a cost-optimized Design and Production Service.

Due to the Hilscher network controller netX, a 10-years delivery guarantee is granted.

Technical Details

NJ 100EN-REParameterValue
ProductPart number1625.100
Brief descriptionExchangeable Module PCI Express
Communication controllernetXnetX 100
Integrated MemoryRAM8 MB SDRAM
FLASH4 MB serial Flash EPROM
Power supply and currentSupply voltage+3.3 V ± 5 % DC
Typical/maximum current750 mA
Typical power consumption2,5 W
System interfaceBus typePCI-Express, One-Lane-Port
Connector type40 pin connector (SAMTEC FSI-120-03-G-D-AB)
Pin distance/pin width0.45 mm/0.55 mm
Transmission rate1,5 GHz
Communication interfaceCommunication standard (protocol)Ethernet
Interface type100 BASE-TX, isolated or 10 BASE-T (depending on loaded firmware), Half duplex/Full duplex (at 100 MBit/s if supported by protocol), Auto-Negotiation (if supported by protocol), Auto-Crossover (if supported by protocol)
Diagnostic interfaceTypeUSB
ConnectorSignal at host interface. Available only if integrated in host system
DisplayDisplaySYS System Status, green: RUN, yellow: RDY
COM0, COM1 Communication status, both green/red
TX/RX0, TX/RX1, Ethernet activity status, yellow
LINK0, LINK1, Ethernet link status, green
EnvironmentAmbient temperature range for operation-20 °C … +65 °C
DeviceDimensions (L x W x H)Length 62 mm (with RJ45 connector), 60 mm (without RJ45 connector), width 53.4 mm (at front panel), 50.4 mm (at body), height 25.2 mm (at front panel), 19.2 mm (at body)
Weightapprox. 60 g
HousingClosed module
Protection classIP40
Mounting/InstallationVia milled footprint holes in the carrier board and retaining brackets. No mounting accessories required.
Mounting/pulling cyclesmax. 10
ConfigurationConfiguration softwareSYCON.net
UL certificationUL typecURus
UL fileE334100
Conformance with EMC directivesCE Signyes
EmissionEN55011:2009; CISPR 11, class A
Immunityaccording to EN 61131-2:2003
Electrostatic discharge (ESD) according to IEC/EN61000-4-2 (Air discharge method)IEC/EN 61000-4-2:2009: ± 8 kV, Criterion A
Electrostatic discharge (ESD) according to IEC/EN 61000-4-2 (Contact discharge method)IEC/EN 61000-4-2:2009: ± 4 kV, Criterion A
Fast transient interferences (Burst), according to IEC/EN 61000-4-4IEC/EN 61000-4-4:2004+A1:2010: ± 1.1 kV, Criterion A
Surge voltage, according to IEC/EN 61000-4-5 (Communication and data lines)IEC/EN 61000-4-5:2006: 1 kV, Criterion A
TestsShockEN60068-2-27 Ea
VibrationEN60068-2-6 Fc

Ordering information

Product namePart numberBrief description
NJ 100EN-RE/PNS V31625.100/PNS V3Exchangeable Module PCI Express - PROFINET IO Device


Product namePart numberBrief description
NJEB-E1600.010netJACK Evaluation Board PCI ExpressShow product

The netJACK exchangeable module comes in a closed IP 40 housing and is a universal solution for upgrading devices with master or slave functionality. All of the designs have the same mechanics as well as an identical software interface. The exchangeable module can easily be installed by the user at any point of the delivery chain without tools.

Brochures, Whitepaper and Case Studies

Find all our current Media to Embedded Modules at our Media Archive.