Exchangeable Module PCI Express - Open Modbus/TCP

    Can be mounted at any point of the delivery chain

    Product Image


    NJ 100EN-RE_OMB-Image

    NJ 100EN-RE


    At a glance

    • Universal Master - Slave interface in closed IP40 housing
    • Host connection via PCI Express
    • One hardware for all Real-Time Ethernet protocols
    • Easy slide-in mounting without tools
    • Locks and connects without additional components on the baseboard
    • Firmware update via integrated WebServer

    Weitere Informationen


    The PCI Express communication module

    The universal communication module netJACK with its PCI Express interface addresses in particular the embedded market with high-performance CPUs like Intel Atom®. Alternatively, there are versions with a traditional dual-port memory and a fast serial SPI interface.

    All types have the compact design of a closed IP 40 module which can be mounted without using tools. Additional costs for the device will not arise because connector and mounting rails are designed as contact areas and cut-outs on the baseboard.

    netJACK can be mounted quickly and easily right before shipment - or even by the end customer.

    With netJACK customers can realize the full range of communication solutions, e.g. for drives, HMI or ident systems. At the same time, additional functionalities as PLC, visualization or individual applications are possible. For customer-specific requirements, Hilscher offers a cost-optimized Design and Production Service.

    Due to the Hilscher network controller netX, a 10-years delivery guarantee is granted.

    Technical Details

    NJ 100EN-REParameterValue
    ProductPart number1625.100
    Brief descriptionExchangeable Module PCI Express
    Communication controllernetXnetX 100
    Integrated MemoryRAM8 MB SDRAM
    FLASH4 MB serial Flash EPROM
    Power supply and currentSupply voltage+3.3 V ± 5 % DC
    Typical/maximum current750 mA
    Typical power consumption2,5 W
    System interfaceBus typePCI-Express, One-Lane-Port
    Connector type40 pin connector (SAMTEC FSI-120-03-G-D-AB)
    Pin distance/pin width0.45 mm/0.55 mm
    Transmission rate1,5 GHz
    Communication interfaceCommunication standard (protocol)Ethernet
    Interface type100 BASE-TX, isolated or 10 BASE-T (depending on loaded firmware), Half duplex/Full duplex (at 100 MBit/s if supported by protocol), Auto-Negotiation (if supported by protocol), Auto-Crossover (if supported by protocol)
    Diagnostic interfaceTypeUSB
    ConnectorSignal at host interface. Available only if integrated in host system
    DisplayDisplaySYS System Status, green: RUN, yellow: RDY
    COM0, COM1 Communication status, both green/red
    TX/RX0, TX/RX1, Ethernet activity status, yellow
    LINK0, LINK1, Ethernet link status, green
    EnvironmentAmbient temperature range for operation-20 °C … +65 °C
    DeviceDimensions (L x W x H)Length 62 mm (with RJ45 connector), 60 mm (without RJ45 connector), width 53.4 mm (at front panel), 50.4 mm (at body), height 25.2 mm (at front panel), 19.2 mm (at body)
    Weightapprox. 60 g
    HousingClosed module
    Protection classIP40
    Mounting/InstallationVia milled footprint holes in the carrier board and retaining brackets. No mounting accessories required.
    Mounting/pulling cyclesmax. 10
    UL certificationUL typecURus
    UL fileE334100
    Conformance with EMC directivesCE Signyes
    EmissionEN55011:2009; CISPR 11, class A
    Immunityaccording to EN 61131-2:2003
    Electrostatic discharge (ESD) according to IEC/EN61000-4-2 (Air discharge method)IEC/EN 61000-4-2:2009: ± 8 kV, Criterion A
    Electrostatic discharge (ESD) according to IEC/EN 61000-4-2 (Contact discharge method)IEC/EN 61000-4-2:2009: ± 4 kV, Criterion A
    Fast transient interferences (Burst), according to IEC/EN 61000-4-4IEC/EN 61000-4-4:2004+A1:2010: ± 1.1 kV, Criterion A
    Surge voltage, according to IEC/EN 61000-4-5 (Communication and data lines)IEC/EN 61000-4-5:2006: 1 kV, Criterion A
    TestsShockEN60068-2-27 Ea
    VibrationEN60068-2-6 Fc

    Ordering information

    Product namePart numberBrief description
    NJ 100EN-RE/OMB1625.100/OMBExchangeable Module PCI Express - Open Modbus/TCP


    Product namePart numberBrief description
    NJEB-E1600.010netJACK Evaluation Board PCI ExpressShow product

    The netJACK exchangeable module comes in a closed IP 40 housing and is a universal solution for upgrading devices with master or slave functionality. All of the designs have the same mechanics as well as an identical software interface. The exchangeable module can easily be installed by the user at any point of the delivery chain without tools.