Logo Hilscher

Technologies

    Exchangeable Module Dual-port memory - Open Modbus/TCP

    Can be mounted at any point of the delivery chain

    Product Image

     

    NJ 100DN-RE_OMB-Image

    NJ 100DN-RE

    Active

    At a glance

    • Universal Master - Slave interface in closed IP40 housing
    • Host connection via Dual-Port Memory
    • One hardware for all Real-Time Ethernet protocols
    • Easy slide-in mounting without tools
    • Locks and connects without additional components on the baseboard
    • Firmware update via integrated WebServer

    Weitere Informationen

    Description

    The PCI Express communication module

    The universal communication module netJACK with its PCI Express interface addresses in particular the embedded market with high-performance CPUs like Intel Atom®. Alternatively, there are versions with a traditional dual-port memory and a fast serial SPI interface.

    All types have the compact design of a closed IP 40 module which can be mounted without using tools. Additional costs for the device will not arise because connector and mounting rails are designed as contact areas and cut-outs on the baseboard.

    netJACK can be mounted quickly and easily right before shipment - or even by the end customer.

    With netJACK customers can realize the full range of communication solutions, e.g. for drives, HMI or ident systems. At the same time, additional functionalities as PLC, visualization or individual applications are possible. For customer-specific requirements, Hilscher offers a cost-optimized Design and Production Service.

    Due to the Hilscher network controller netX, a 10-years delivery guarantee is granted.

    Technical Details

    NJ 100DN-RE Parameter Value
    ProductPart number1623.100
    Brief descriptionExchangeable Module Dual-port memory
    Communication controllernetXnetX 100
    Integrated MemoryRAM8 MB SDRAM
    FLASH4 MB serial Flash EPROM
    Power supply and currentSupply voltage+3.3 V ± 5 % DC
    Typical/maximum current556-640 mA
    Typical power consumption1,83 W
    System interfaceBus typeParallel dual-port memory
    Connector type80 pin connector (SAMTEC FSI-140-03-G-D-AB)
    Pin distance/pin width0.45 mm/0.55 mm
    Dual-port-memory size64 KB (16 address lines), where 16 KB used by firmware (14 address lines, lowest 16 KB)
    Width for the data access to the Dual-Port Memory (DPM)8/16 bit
    Communication interfaceCommunication standard (protocol)Ethernet
    Interface type100 BASE-TX, isolated or 10 BASE-T (depending on loaded firmware), Half duplex/Full duplex (at 100 MBit/s if supported by protocol), Auto-Negotiation (if supported by protocol), Auto-Crossover (if supported by protocol)
    Connector2xRJ45
    Diagnostic interfaceTypeUSB or UART
    ConnectorSignal at host interface. Available only if integrated in host system
    DisplayDisplaySYS System Status, green: RUN, yellow: RDY
    COM0, COM1 Communication status, both green/red
    TX/RX0, TX/RX1, Ethernet activity status, yellow
    LINK0, LINK1, Ethernet link status, green
    EnvironmentAmbient temperature range for operation-20 °C … +70 °C
    Ambient temperature range for storage-10 °C … +70 °C
    DeviceDimensions (L x W x H)Length 62 mm (with RJ45 connector), 60 mm (without RJ45 connector), width 53.4 mm (at front panel), 50.4 mm (at body), height 25.2 mm (at front panel), 19.2 mm (at body)
    Weight< 80 g
    HousingClosed module
    Protection classIP40
    Mounting/InstallationVia milled footprint holes in the carrier board and retaining brackets. No mounting accessories required.
    Mounting/pulling cyclesmax. 10
    ConfigurationConfiguration softwareSYCON.net
    ConformityRoHSyes
    Reachyes
    UL certificationUL typecURus
    UL fileE334100
    Conformance with EMC directivesCE Signyes
    EmissionEN55011:2009; CISPR 11, class A
    Immunityaccording to EN 61131-2:2003
    Electrostatic discharge (ESD) according to IEC/EN61000-4-2 (Air discharge method)IEC/EN 61000-4-2:2009: ± 8 kV, Criterion A
    Electrostatic discharge (ESD) according to IEC/EN 61000-4-2 (Contact discharge method)IEC/EN 61000-4-2:2009: ± 6 kV, Criterion A
    Fast transient interferences (Burst), according to IEC/EN 61000-4-4IEC/EN 61000-4-4:2004+A1:2010: ± 4.4 kV, Criterion A
    Surge voltage, according to IEC/EN 61000-4-5 (Communication and data lines)IEC/EN 61000-4-5:2006: 1 kV, Criterion A
    TestsShockEN60068-2-27 Ea
    VibrationEN60068-2-6 Fc

    Ordering information

    Product name Part number Brief description
    NJ 100DN-RE/OMB1623.100/OMBExchangeable Module Dual-port memory - Open Modbus/TCP

    Accessories

    Product name Part number Brief description
    NJEB-D1600.000netJACK Evaluation Board PCI ExpressShow product

    The netJACK exchangeable module comes in a closed IP 40 housing and is a universal solution for upgrading devices with master or slave functionality. All of the designs have the same mechanics as well as an identical software interface. The exchangeable module can easily be installed by the user at any point of the delivery chain without tools.