Logo Hilscher

Technologies

  • DeviceNet
  •  

Communication Module SPI -DeviceNet Slave

The module for all communication tasks

Product Image

 

COMX 10CA-DN_Image

COMX 10CA-DNS

Active

At a glance

  • Complete slave interface with network connector onboard
  • Host connection via dual-port memory or SPI
  • Allows one baseboard design for all networks

Weitere Informationen

Description

The module for all communication tasks

The comX communication module has been designed to be integrated into automation devices e.g. robot controllers, PLCs or drives to add a network interface. All communication tasks are executed autonomously within the module - irrespective of the processor of the target device.

Process data is exchanged via a Dual-Port-Memory which is accessed either by an 8-/16-bit bus interface or a fast 50 MHz SPI interface.

comX supports all major Real-Time Ethernet protocols as Master or Slave and covers all network-specific demands in just one single module. To support a line topology, the module is equipped with two Ethernet ports. The communication protocol can be changed simply and reliably by loading the appropriate firmware and a software license for masters.

Due to the Hilscher network controller netX, a 10-years delivery guarantee is granted.

Technical Details

COMX 10CA-DNS Parameter Value
ProductPart number1561.520
Brief descriptionCommunication Module DeviceNet Slave
Communication controllernetXnetX 10
Integrated MemoryFLASH4 MB serial Flash
Power supplySupply voltage+3.3 V DC ± 5 %
Typical/maximum currentapprox. 250 mA/290 mA (at 3.3 V)
Typical power consumptionapprox. 0.825 W
Power connectorvia system bus connector X1
System interfaceTypeParallel or serial dual-port memory interface
Connector50-pin SMT, female connector
Pin distance1.27 mm
Dual-port memory size16 KByte (lowest 8 KByte used by firmware)
Data width8/16 bit
Serial dual-port memory interfaceSPI Slave, mode 3
Baud ratemax. 50 MHz
Communication interfaceCommunication standardDeviceNet Slave
Interface typeISO-11898, according to DeviceNet specification, potential-free
ConnectorCOMBICON, plug, 5-pin
Diagnostic interfaceTypeUART or USB
ConnectorSignal at host interface. Available only if integrated in host system.
DisplayLED displaySYS System Status, green: RUN, yellow: RDY
MNS Module network status, green: MS, red: NS
Operating elementsNetwork address2 rotary switches for address
EnvironmentAmbient temperature range for operation-20 °C … +70 °C (Air flow during measurment: 0,5 m/s)
Ambient temperature range for storage-10 °C … +70 °C
Humidity range10 % … 95 % relative humidity (non-condensing)
DeviceDimensions (L x W x H)70 mm x 30 mm x 21.5 mm
Weightapprox. 35 g ... 40 g
Mountingusing screwable metal bolts, according to comX Design Guide
ConfigurationConfiguration softwareSYCON.net
ConformityRoHSyes
Conformance with EMC directivesCE signyes
EmissionEN 61000-6-4
ImmunityEN 61000-6-2
Electrostatic discharge (ESD) according to EN 61000-4-2 (Air discharge method)EN 61000-4-2: ± 10 kV, Criterion B
Electrostatic discharge (ESD) according to EN 61000-4-2 (Contact discharge method)EN 61000-4-2: ± 6 kV, Criterion B
Fast transient interferences (Burst) according to EN 61000-4-4EN 61000-4-4: ± 2 kV, Criterion B (Communication lines, shielded)
Surge voltage according to EN 61000-4-5 (Communication and data lines)EN 61000-4-5: 0.5 kV, Criterion B (Communication lines, shielded)

Ordering information

Product name Part number Brief description
COMX 10CA-DNS1561.520/DNSCommunication Module SPI -DeviceNet Slave

The comX communication module is a universal solution for upgrading devices with master or slave functionality. All modules are pin-compatible and have an identical software interface.
There are designs with an integrated network connector and designs in which the network interface is tied to the base board.