Communication Module Dual-port memory - Open Modbus/TCP

    The module for all communication tasks

    Product Image


    COMX 100CN-RE-Image

    COMX 100CN-RE


    At a glance

    • Universal master / slave interface with network connection to the baseboard
    • Host connection via dual-port memory
    • One hardware for all Real-Time Ethernet protocols
    • Enables flexible positioning of the network connector
    • Firmware update via integrated WebServer

    Weitere Informationen


    The module for all communication tasks

    The comX communication module has been designed to be integrated into automation devices e.g. robot controllers, PLCs or drives to add a network interface. All communication tasks are executed autonomously within the module - irrespective of the processor of the target device.

    Process data is exchanged via a Dual-Port-Memory which is accessed either by an 8-/16-bit bus interface or a fast 50 MHz SPI interface.

    comX supports all major Real-Time Ethernet protocols as Master or Slave and covers all network-specific demands in just one single module. To support a line topology, the module is equipped with two Ethernet ports. The communication protocol can be changed simply and reliably by loading the appropriate firmware and a software license for masters.

    Due to the Hilscher network controller netX, a 10-years delivery guarantee is granted.

    Technical Details

    COMX 100CN-REParameterValue
    ProductPart number1531.101
    Brief descriptionCommunication Module Real-Time Ethernet
    Communication controllernetXnetX 100
    Integrated MemoryRAM8 MB SDRAM
    FLASH4 MB serial Flash
    Power supplySupply voltage+3.3 V DC ± 5 %
    Typical/maximum currentapprox. 700 mA/750 mA (at 3.3 V)
    Typical power consumptionapprox. 2.5 W
    Power connectorvia system bus connector X1
    System interfaceTypeParallel Dual-port memory interface
    Connector50-pin SMT, female connector
    Pin distance1.27 mm
    Dual-port memory size16 KByte
    Data width8/16 bit
    Communication interfaceCommunication standardEthernet
    Interface type10BASE-T/100BASE-TX, potential-free
    Auto negotiationsupported
    Auto cross oversupported
    Connector30-pin SMT connector, female, grid distance 1.27 mm, matching with plug type SAMTEC TFM-115-02-S-D–A
    Diagnostic interfaceTypeUART or USB
    ConnectorSignal at host interface. Available only if integrated in host system.
    DisplayLED displaySignals at X2 for SYS System Status, green: RUN, yellow: RDY
    Signals at X2 for COM0, COM1 Communication status, both green/red
    Signals at X2 for TX/RX0, TX/RX1, Ethernet activity status, yellow
    Signals at X2 for LINK0, LINK1, Ethernet link status, green
    EnvironmentAmbient temperature range for operation-20 °C … +70 °C (Air flow during measurment: 0,5 m/s)
    Ambient temperature range for storage-10 °C … +70 °C
    Humidity range10 % … 95 % relative humidity (non-condensing)
    DeviceDimensions (L x W x H)70 mm x 30 mm x 21.5 mm
    Weightapprox. 35 g ... 40 g
    Mountingusing screwable metal bolts, according to comX Design Guide
    Conformance with EMC directivesCE signyes
    EmissionEN 61000-6-4
    ImmunityEN 61000-6-2
    Electrostatic discharge (ESD) according to EN 61000-4-2 (Contact discharge method)EN 61000-4-2: ± 4 kV, Criterion B
    Fast transient interferences (Burst) according to EN 61000-4-4EN 61000-4-4: ± 2 kV, Criterion B (Communication lines, shielded)
    Surge voltage according to EN 61000-4-5 (Communication and data lines)EN 61000-4-5: 1 kV, Criterion A (Communication lines, shielded)

    Ordering information

    Product namePart numberBrief description
    COMX 100CN-RE/OMB1532.100/OMBCommunication Module Dual-port memory - Open Modbus/TCP

    The comX communication module is a universal solution for upgrading devices with master or slave functionality. All modules are pin-compatible and have an identical software interface.
    There are designs with an integrated network connector and designs in which the network interface is tied to the base board.