netX 52 Chip-Carrier inkl. Übertrager - Real-Time-Ethernet-Slave

Lötfertiges netX-Design im Briefmarkenformat

Komplette Slave-Schnittstelle auf kleinster Fläche
Deutliche Platzersparnis durch integrierte Übertrager
Host-Anbindung über Dual-Port-Memory oder SPI
Eine Hardware für alle Real-Time-Ethernet Systeme

Real-Time Ethernet solution in the smallest space

The rapid and secure alternative to a slave interface developed by the customer is netRAPID. The compact, stamp-sized, 32 x 32 mm netX Chip Carrier is a solution that offers adequate costs per unit, a reduced risk, and a fast time-to-market. Like a standard QFP component, it will be soldered directly to the host system - by hand or SMD production process.

Optimized for minimum space requirements, netRAPID 52-RE contains all necessary operating components, such as Ethernet transformers, SQI Flash, and netX multi-protocol chip. Real-Time Ethernet communication is in focus. The protocol stack will be executed in the internal RAM of the netX. Thus, the hardware developer only needs to integrate network connectors, LEDs, and address switches on the host system. For the host system, a simple 2-layer printed circuit board is sufficient. The application development is reduced to the use of the API of the netRAPID.

To be able to profit from the full function of netRAPID, the licensed firmware must be acquired once and loaded during the manufacturing process.

Product	Product name	NRP 52
	Part number	7670.100
	Brief description	Chip carrier with Ethernet interface
Network controller	netX	netX 52
Integrated Memory	RAM	4 MB serial Flash EPROM
Power supply and current	Supply voltage	+3,3 V DC ± 5 %
	Maximum current (typically)	520 mA/600 mA (at 3,3 V)
	Power consumption (typical)	1.8 W
Host interface	Type	Parallel dual-port memory or serial dual-port memory (SPI, mode 3)
	Connector	76-pin solder contacts 1 mm with 1.5 mm grid
	Dual-port memory size	16 KB (14 address lines)
	Width for the data access to the dual-port memory (DPM)	8 or 16 bit
	Baud rate (serial dual-port memory)	Max. 50 MHz
Communication interface	Communication standard	Ethernet
Communication interface	Interface type	100BASE-TX or 10BASE-T, isolated
Diagnostic interface	Type	USB or UART, the support of the diagnostic interface depends on the loaded firmware
Diagnostic interface	Connector	USB or UART: Signals at Chip Carrier, available only if integrated in host system
Display	LED displays	SYS System status
		COM0, COM1 Communication status
		2 x Link and 2 x Activity
Permitted ambient conditions	Ambient temperature range for operation	-20 … +70 °C (at an airflow of 0.5 m/s)
Device	Dimensions (L x W x H)	32 mm x 32 mm x 4 mm
Device	Weight	approx. 4 g
Conformance with EMC directives	Emission	EN 55011:2009 + A1:2010 Class B (Conducted), A (Radiated)
	Electrostatic discharge (ESD) according to IEC/EN 61000-4-2:1995 (Contact discharge method)	6 kV Criterion A
	Radiated RF, according to IEC/EN 61000-4-3 and IEC/ EN 55011 80-1000MHz, 10V/m, 80% AM / 1kHz	Class A
	Radiated RF, according to IEC/EN 61000-4-3:2006 1.0-2.7 GHz, 10V/m, 80% AM / 1kHz	Class A
	Fast transient interferences (Burst), according to IEC/EN 61000-4-4:1995 (Communication and data lines)	2.2 kV Criterion B
	Surge voltage, according to IEC/EN 61000-4-5:1995 (Communication and data lines)	1 kV Criterion B
	Conducted RF, according to IEC/EN 61000-4-6:2009 0,15-80 MHz, 80% AM / 1kHz	Class A

Product name	Part number	Brief description
NRP 52-RE	767x.100	netX 52 Chip Carrier incl. transformer - Real-Time Ethernet slave

Download Software

Open page [English]

Download Technische Dokumentation

Download Datenblätter

Accessory

NRPEB 52-RE

netRAPID 52 Evaluation Board - Real-Time-Ethernet

Serie

Mehr erfahren