Logo Hilscher

Technologies

  • CANopen
  • PROFIBUS
  • CC-Link
  • DeviceNet
  • EtherCAT
  • EtherNet/IP
  • IO-Link
  • POWERLINK
  • PROFINET
  • Sercos
  • SmartWire-DT
  •  

Network controller for fieldbus and Real-Time Ethernet slaves

Product Image

 

NETX 52-Image

NETX 52

Active

At a glance

  • Flexible „high end“ network controller equipped with a host interface or stand-alone solution for digital I/Os
  • Two communication channels for Real-Time Ethernet equipped with PHY or fieldbus
  • Extended communication functions support amongst others, PROFINET V2.3 - Dynamic Frame Packing and IO-Link V1.1
  • Second RISC CPU for time-critical I/O tasks
  • Fast SPI host interface with Read/Write functions

Weitere Informationen

Description

Real-Time Ethernet systems are successfully used and further developed in many applications. Thus, the demands on the resources and functionalities of network controllers are increasing. netX 51/52 network controllers are based on the further developed netX 50 communication architecture which features considerably more internal storage capacity and additional function units. The hardware of netX 51 and netX 50 is compatible. netX 52 consists of the same silicon, but dispenses with an external memory bus and is more cost-effective due to its smaller housing. These three components are thus optimized for designing modular or compact slaves, or as a Real-Time Ethernet controller of a high-performance CPU. The communication channels meet all actual and future requirements of the PROFINET Specification V2.3, as e.g. ”Dynamic Frame Packing“. Moreover, the application of the new PHYs manufactured by Renesas ensures faster throughput times and expanded diagnosis properties.

In connection with a small QSPI Flash the internal memory of more than 670 KByte enables very compact solutions doubling the performance of the netX 50. For processing fast IOs, the application is provided with a second RISC CPU. It works in parallel to the ARM and significantly reduces the demands on the ARM software in case of short bus cycle times. Typical applications are IO-Link Master Gateways. When using gateways, the xPIC carries out the IO-Link data transfer so that the ARM is fully available for processing the transmission protocol to the master. A third Ethernet interface for connecting a PC for diagnosis and configuration purposes is implemented. Alternatively, it can also be used for connecting the netX to a host CPU. On this MII interface the netX will behave like a PHY.

Some Real-Time Ethernet systems use the CANopen object models or the same communication services as with Ethernet/IP and DeviceNet. This makes it necessary to connect CAN to the Real-Time Ethernet system as a “legacy network”. So far, this task required the use of the expensive netX 100 controller with its three communication channels. As an alternative, a dedicated CAN controller is available now.

Owing to these possibilities, the netX 51/52 is significantly more than just a Real-Time Ethernet interface chip equipped with a dual-port memory.

Ordering information

Product name Part number Brief description
NETX 522232.001Network controller for fieldbus and Real-Time Ethernet slaves

Accessories

Product name Part number Brief description
NXHX 52-JTAG7773.300Development boardShow product
NXLFW-COS7428.540Loadable Firmware CANopen SlaveShow product
NXLFW-CCS7428.740Loadable Firmware CC-Link SlaveShow product
NXLFW-DNS7428.520Loadable Firmware DeviceNet SlaveShow product
NXLFW-DPS7428.420Loadable Firmware PROFIBUS DP SlaveShow product
NXLFW-EIS7428.830Loadable Firmware EtherNet/IP AdapterShow product
NXLFW-OMB7428.860Loadable Firmware Open Modbus/TCPShow product
NXLFW-ECS7428.120Loadable Firmware EtherCAT SlaveShow product
NXLFW-PNS7428.851Loadable Firmware PROFINET IO DeviceShow product
NXLFW-S3S7428.160Loadable Firmware Sercos SlaveShow product